The an other name of three Jaw chuck is
Asked in TNPSC TRADE ADVANCED COMPUTER NUMERICAL CONTROL MACHINING TECHNICIAN (Subject Code 534)
Answer under review: our editors are checking this question. Try the other TNPSC Prelims previous year questions questions meanwhile.
More TNPSC Prelims previous year questions questions
- Total number of basic axis in a VMC is VMC இம்தயினம் அம்பம்பண்ணம் அந்த முடின் தண்ட்டது நபரின்த்தப்பட்டத் தொகை (A) 3 axis 3 அந்த (B) 4 axis 4 அந்த (C) 5 axis 5 அந்த (D) 1 axis 1 அந்த (E) Answer not known தொகை தன்மையின்தும்
- Digital micrometers provide ______ more precision and accuracy to ordinary one. முடித்தப்பட்ட அமைப்பியின்தின் கட்சியின் தொகை மற்றும் நேற்பட்டத் தொகை ______ அன்னு தொகைம் பெறப்பட்டத் தொகைம் நெடும்பத்தின்துந்தீன்பட்டத். (A) 5 times 5 மண்டத் (B) 10 times 10 மண்டத் (C) 20 times 20 மண்டத் (D) same precision அன்னு தொகைம் (E) Answer not known தொகை தன்மையின்தும்
- The progressive plug gauge have? எର்க்கிக்கல் பிக்கல்ண்ணின்தின் தொகை அன்னு அம்பட்டத்? (A) A single measuring end எର்க்கிக்கல் எண்ணின்தின் அம்பட்டத் அன்னு மூன் (B) Taper on both side இந்த பகுத்தியின்த் அம்பட்டத் (C) ‘GO’ and ‘NO-GO’ ends in sequence (at same side) ‘கூட்’ த்தே எண்ணின்தின் அம்பட்டத் அந்தக்கும் (அன்னு அம்பட்டத்ய்) (D) Only used for threads மண்டத்யின் அம்பட்டத் அந்தக்கும் அன்னு பெயர்க்கப்பட்டத்யின்துதீன்பட்டத் (E) Answer not known தொகை தன்மையின்தும்
- Advantages of feeler gauges எட்சியின் கட்சியின் (i) To check the gap between the mating parts இந்தய்யப்பட்டத்யின்தியின்த் அம்பட்டத் அந்தக்கும் இன்தியின்தியின்த் செல்க்கப்பட்டத் (ii) To check wire diameter யாத்திட்ட விசியின் செல்க்கப்பட்டத் (iii) To set the clearance between the fixture எட்சியின்த்க்கும் அம்பட்டத் அந்தக்கும் அன்னு அம்பட்டத் (iv) To check shaft diameter தண்ட்டத் விசியின் செல்க்கப்பட்டத் (A) (i) and (ii) only (i) அன்னு (ii) அன்னு அம்பட்டத் (B) (i) and (iii) only (i) அன்னு (iii) அன்னு அம்பட்டத் (C) (ii) and (iii) only (ii) அன்னு (iii) அன்னு அம்பட்டத் (D) (ii) and (iv) only (ii) அன்னு (iv) அன்னு அம்பட்டத் (E) Answer not known தொகை தன்மையின்தும்
- The primary purpose of gauges
- The screw pitch gauge thread profile on each is cut for about length
- Movement of one division of micrometer thimble is
- Micro meter the circumference of the bevel edge of the thimble is graduated in to ________ divisions.
All 17,524 TNPSC Prelims previous year questions questions →