Consider the following statements regarding composite materials: Statement I: In a composite material, the matrix phase is also known as continuous phase. Statement II: In a composite material, the matrix phase transfers load to the reinforcement phase. Statement III: Composite materials are generally isotropic in nature. Statement IV: Composite materials always have lower strength than their individual constituents. Which of the above statements are correct?
Asked in GPSC Graduate Engineer Trainee, Class-2, Gujarat Maritime Board (GMB) 2026
Show answer
Answer: A. I and II only
This previous-year question came without the commission's answer key; the answer was checked by AI. Always confirm with the official key.
More GPSC Prelims previous year questions questions
- Consider the following statements regarding solid solutions: Statement I: In an interstitial solid solution, the solute atoms occupy the interstitial spaces between the solvent atoms. Statement II: Substitutional solid solutions are formed only when the solute and solvent have identical atomic sizes. Statement III: Carbon dissolved in iron is an example of an interstitial solid solution. Statement IV: Interstitial solid solutions are generally formed by solute atoms that are larger than the solvent atoms. Which of the above statements are correct?
- Consider the following statements regarding the iron–carbon equilibrium diagram: Statement I: The eutectoid reaction occurs at 727°C and 0.76% carbon. Statement II: The eutectic reaction occurs at 1147°C and 4.3% carbon. Statement III: The peritectic reaction occurs at 1493°C. Which of the above statements are correct?
- Consider the following statements regarding High-Strength Low-Alloy (HSLA) steels: Statement I: HSLA steels contain alloying elements such as copper, vanadium, nickel and molybdenum. Statement II: HSLA steels possess higher strengths than the plain low-carbon steels. Statement III: In normal atmospheres, the HSLA steels are more resistant to corrosion than the stainless steels. Statement IV: HSLA steels possess high tensile strengths and are ductile, formable and machinable. Which of the above statements are correct?
- Consider the following statements regarding herringbone gears: Statement I: A herringbone gear comprises teeth having both right- and left-hand helix cut on the same gear blank. Statement II: The axial force of the right-hand half of the herringbone gear is balanced by that of the left-hand half. Statement III: For the efficient transmission of large amounts of power at high speeds, herringbone gears are almost universally employed. Statement IV: Helix angles are usually larger for herringbone gears than for single-helical gears.
- Consider the following statements regarding balancing in linkages: Statement I: Balancing in linkages directly addresses balancing the shaking force only. Statement II: Force balancing a linkage is directly related to the position of the total center of mass. Statement III: The method of static balancing, in which concentrated link masses are replaced by systems of masses that are statically equivalent. Which of the above statements are correct?
- Consider the following statements about governors: Statement I: In a centrifugal governor, it is the radial (normal) component of the acceleration that is primarily responsible for creating the controlling force. Statement II: In an inertia shaft governor, radial component of acceleration is small and much less effective. Statement III: An inertia governor is less sensitive as compared with a centrifugal governor. Which of the above statements are correct?
- Consider the following statements regarding Gruebler's criterion for planar mechanisms: Statement I: Gruebler's criterion is used in kinematics to determine the degrees of freedom of a planar mechanism. Statement II: For a planar mechanism, Gruebler's criterion is defined as F = 3(n–1) – 2j1 – j2, Where F is degrees of freedom, n is total number of links in the mechanism, j1 is number of lower pairs and j2 is number of higher pairs. Statement III: A planar four-bar mechanism has two degrees of freedom. Which of the above statements are correct?
- Consider the following statements regarding cam pairs and degrees of freedom: Statement I: A cam pair has two degrees of freedom. Statement II: A cam pair can be replaced by one binary link with two turning pairs at each end. Statement III: To have one cam pair in a mechanism with one degree of freedom, if the mechanism has three links, then turning pairs should be two. Statement IV: To have one cam pair in a mechanism with one degree of freedom, if the mechanism has three links, then turning pairs should be five. Which of the above statements are correct?